Pedestrian Crash Sensor Calibration

Pedestrian Crash Sensor Calibration- Procedure NOTE: When you replace or remove the pedestrian crash sensor and/or the safety plate, calibrate the pedestrian crash sensor with the HDS. When you replace or update the SRS unit, calibrate the pedestrian crash sensor with the HDS. When you do the VSA sensor neutral …

Read More »

VSA Sensor Neutral Position Memorization

VSA Sensor Neutral Position Memorization- Procedure NOTE: The VSA sensor neutral position must be learned whenever you do any of these actions: Update or replace the VSA modulator-control unit. Update or replace the SRS unit. Remove the steering wheel. Disconnect the steering joint. Wheel alignment adjustment. Before doing the memorization …

Read More »

How to Troubleshoot the EPS

How to Troubleshoot the EPS 2239 System Indicator This system has one (without LKAS (Lane Keep Assist System)) or two (with LKAS) indicators on the gauge control module. EPS Indicator Under normal conditions, the EPS indicator comes on when turning the vehicle to the ON mode, then turns off after …

Read More »

Steering Angle Neutral Position Learning

Steering Angle Neutral Position Learning- Procedure NOTE: If the steering angle neutral position is cleared, do the steering angle neutral position learning procedure. The steering angle neutral position is cleared whenever you do any of these actions: EPS motor/control unit replacement, removal, or installation. 12 volt battery terminal is disconnected …

Read More »

12 Volt Battery Sensor Replace

12 Volt Battery Sensor Removal and Installation 12 Volt Battery Sensor – Remove Make sure the vehicle is in the OFF (LOCK) mode. Disconnect the connector (A). Disconnect the cable (B) from the 12 volt battery sensor (C). Remove the 12 volt battery sensor from the 12 volt battery. NOTE: …

Read More »

P154A Battery Sensor Internal Failure

DTC P154A: Battery Sensor Internal Failure NOTE: Before you troubleshoot, review the general troubleshooting information. Turn the vehicle to the ON mode. Clear the DTC with the HDS, and wait 5 seconds. Check for Pending or Confirmed DTCs with the HDS. Is DTC P154A indicated? Yes The failure is duplicated. …

Read More »

Catalytic Converter Replace

1. A/F Sensor Removal and Installation- Removal / Installation Disconnect Connector (A/F Sensor) A/F Sensor – Remove Using the sensor socket wrench, remove the A/F sensor. 2. EGR Valve (Exhaust gas recirculation) and EGR Pipe Removal and Installation NOTE: Although a numbered sequence is shown, these “*” indicated parts are …

Read More »

Vehicle Lift and Support Points

NOTE: If you are going to remove heavy components such as suspension or the fuel tank from the rear of the vehicle, first support the front of the vehicle with tall safety stands. When substantial weight is removed from the rear of the vehicle, the center of gravity can change, …

Read More »

Fuel and Emissions Systems General Information

Fuel and Emissions Systems General Information Category Term Term Remarks Engine Type 2.0 L/DOHC/PI K20C2 2.0 L/DOHC/DI K20C1 1.5 L/DOHC/DI L15B7, L15BA, L15BB 1.0 L/DOHC/DI P10A2, P10A4 1.8 L/SOHC/PI R18Z1, R18ZK 1.6 L/SOHC/PI R16B2, R16B1 2.0 L/SOHC/PI R20Z5 Fuel Type GAS Petrol E85 Ethanol (alcohol) can be used up to …

Read More »

ECM PCM Reset Procedure

PCM Reset- Procedure 1. Connect – HDS 2. PCM – Reset Select the PGM-FI system with the HDS (Honda Diagnostic System). Reset the PCM with the HDS while the engine is stopped. Turn the vehicle to the OFF (LOCK) mode. Turn the vehicle to the ON mode, and wait 30 …

Read More »

Responsive WordPress Theme Freetheme wordpress magazine responsive freetheme wordpress news responsive freeWORDPRESS PLUGIN PREMIUM FREEDownload theme free